Geared motor JACK24.80

24 Vdc gear motor for side mounting for intensive use, with integrated control unit and encoder

Commercial use

Industrial use

Sectional garage doors

24 Vdc

Up to 35 ㎡

Integrated device that guarantees maximum precision during the automation manoeuvring steps

Intelligent power control system that allows obtaining dynamic data through a precise calculation of the thrust. The system is able to locate any critical points and adjust the torque accordingly in relation to actual requirements and according to measured performance

433.92 MHz Receiver equipped exclusively with Advanced Rolling Code (ARC)

Integrated device that ensures a standby absorption of less than 0.5 W

This is a protocol for connection with KNX home automation systems by connection of the X.BE card (optional)

The control panel can be managed thanks to BeUP app, which recreates the control panel menu to adjust parameters and logic, and read error messages and update the firmware. You can do remote diagnostics, check the status of the gate and send commands

512 transmitters storable inside the receiver


24 Vdc | intensive use

24 Vdc gear motor for side mounting for intensive use, with integrated control unit and encoder | Switching power supply 100÷250 Vac 50/60 Hz which reduces energy consumption and ensures a long lifespan of the actuator | The control unit, easily accessible thanks to the front cover with hinges, is equipped with an innovative system (ESA+) to reduce the energy consumption, which guarantees an absorption in standby below <0.5 W | Equipped with a service light with 14 built-in LED lights that guarantee a high light output | Compact size (11 cm width) that allows a quick and easy mounting even in limited spaces | Ideal for the automation of large doors (up to 35 ㎡) or if an intensive use is required | The encoder guarantees the highest safety and precision during the movement of the door | Built-in STC system for a precise torque management | Operation guaranteed even in the event of a power failure thanks to batteries that can be perfectly integrated in the motor (2 batteries 1.2 Ah) | Anti-crushing system with amperometric obstacle detection | Designed for the connection of the X.BE accessory in order to be integrated with KNX domotics installations and the programming through the app BeUP and the interface PRO.UP | Built-in fast release system

Fixing plate included

Power supply 100 ÷ 250 Vac (50-60Hz)
Motor supply 24 Vdc
Max absorbed current 3,3 ÷ 1,8 A
Max torque 80 Nm
Maximum output rotations 20
Output speed 22 r.p.m.
Shaft hole 1” (25.4 mm)
Duty cycle intensive use
Protection level IP40
Built-in control unit
Integrated receiver
Operating temperature -20°C /+50°C
Door surface area 35 ㎡/max
Weight 7.7 kg



1 lateral operator for JACK24 balanced sectional doors


100÷250 Vac - 50/60 Hz


24 Vdc / 8 A


Integrated LCD Display | Integrated 433.92 MHz 512-code radio receiver with ARC coding | Removable terminal blocks | Absolute Encoder | Automatic, semi-automatic and deadman logic | Step by step, stop, photocell, open and close inputs| Input for N.C or 8K2 sensitive edge | Integrated LED courtesy light | Output for configuration as gate open indicator, service light, second radio channel or area light | Output for 24 Vdc electric lock management | Autosetting of operation parameters | Electronic torque adjustment with automatic calculation for each point in the stroke (STC SYSTEM) | Separate electronic adjustments of opening and closing speeds | Anti-crushing safety through amperometric detection and encoder management | Electronic slowdowns in opening and closing | Integrated ESA SYSTEM+ for energy saving | Set up for connection to KNX systems via X.BE card (optional) | Designed for managing, configuring, diagnosing and updating firmware through the BeUP app, using the PRO.UP accessory | Advantouch system to configure parameters and manage radio transmitters | Number of manoeuvres | Programming access password | Maintenance warning | Built-in battery charger

Technical Drawing JACK24.80