Geared motor BULL624 TURBO.S

Fast 24 Vdc gear motor for intensive use with magnetic limit switches, integrated control unit and virtual encoder

Commercial use

24 Vdc

Up to 600 kg

Gear motor with opening speed higher than standard values

Maximum maneuver speed is 25,5 m/min

Encoder signal recreated by the control unit beginning with the measurements of electric motor operation parameters. It is possible to manage slowing optimally and trace gate travel while providing the torque data in relation to its position to guarantee maximum safety

Intelligent power control system that allows obtaining dynamic data through a precise calculation of the thrust. The system is able to locate any critical points and adjust the torque accordingly in relation to actual requirements and according to measured performance

433.92 MHz Receiver equipped exclusively with Advanced Rolling Code (ARC)

This is a protocol for connection with KNX home automation systems by connection of the X.BE card (optional)

The control panel can be managed thanks to BeUP app, which recreates the control panel menu to adjust parameters and logic, and read error messages and update the firmware. You can do remote diagnostics, check the status of the gate and send commands

512 transmitters storable inside the receiver

BULL624 TURBO.S

24 Vdc | intensive use

Fast 24 Vdc gear motor for intensive use with magnetic limit switches, integrated control unit and virtual encoder | Switching power supply 115/230 Vac which reduces energy consumption and ensures a long lifespan of the actuator | The main control unit, on the top part of the motor, makes it possible to facilitate the wiring procedure and also to calculate the position of the motor starting from the measurement of instantaneous speed (virtual encoder) | The virtual encoder allows proper management of the slowing-down phases, movement tracking (STC system), and torque management in relation to the position of the gate, which guarantees maximum safety | Self-programming with the radio transmitter can be activated at the first installation | Practical cableguides | Maximum performance and speed (25.5 m/min with 600 kg) | Anti-crushing system with amperometric obstacle detection | Safety sensor that stops the motor power supply during release operations | Designed for connection to the X.BE module to integrate the device into KNX home automation systems | Convenient compartment for 2 mod. DA.BT2 2.1 Ah batteries | Metal release lever | Option to operate opposed sliding gates using the SIS accessory

325x100x5 mm, installation template included, motor spacing 300x75 mm, 4 holes Ø 9 mm

Power supply 115 Vac / 230 Vac (50-60Hz)
Motor supply 24 Vdc
Max absorbed current 5 / 3 A
Maximum thrust 330 N
Opening speed 12,5 ÷ 25,5 m/min
Duty cycle 60%
Protection level IP44
Built-in control unit
Integrated receiver
Encoder
Virtual encoder
Magnetic limit switches
Pinion for rack M4 Z18
Operating temperature -20°C /+50°C
Lubrication GREASE
Maximum gate weight 600 kg
Weight 10 kg
N. motors per pallet 40
Kit weight ---
N. kits per pallet ---

CP.B24 TURBO

APPLICATION

1 actuator for sliding gates, series BULL624/1224 TURBO

CONTROL UNIT POWER SUPPLY

115 or 230 Vac (selectable) 50/60Hz

MOTORS POWER SUPPLY

24 Vdc / 20 A

MAIN FUNCTIONS

Integrated LCD display | Integrated 433.92 MHz 512-code radio receiver with ARC coding | Removable terminal boards | Automatic, semi-automatic and deadman’s logic | Motor limit switch inputs | Step by step, open, close and stop inputs | Photocell input (PHO) configurable as active in opening-closing or only in closing phases | Photocell input (PHC) active both in opening and closing phases | Input for N.C or 8K2 sensitive edge | Input for safety sensor | OPEN input configurable as pedestrian | Two outputs configurable as gate open indicator, second radio channel of the incorporated receiver, service light, photocell testing | Predesigned for the operation of opposed sliding gates through SIS synchronisation board (optional) | Predesigned for KNX connection through X.BE board (optional) | Autosetting of operating parameters | Electronic torque adjustment with automatic calculation for each point in the stroke (STC SYSTEM) | Anti-crushing safety thanks to amperometric obstacle detection | Virtual encoder | Adjustable slow-downs | Advantouch system to configure parameters and manage radio transmitters | Number of maneuvers | Programming access password | Maintenance warning | Integrated battery charger, compatible with battery models DA.BT2/DA.BT6

Technical Drawing BULL624 TURBO.S